Elo TouchSystems 2201L Dokumentacja Pobierz pdf (Strona 34)

Strona główna
Elo TouchSystems
Nie
2201L
Dokumentacja

Pobierz
Podziel się

Dzielenie się
Dodaj do moich podręczników
Drukuj

24 Chapter 2 - Controller Jumper Settings

Selecting the Touchscreen Type

The E271-2202 controller is shipped with jumper J5 installed for E274 AccuTouch

5-wire touchscreens. If you are using a 4-wire DuraTouch touchscreen (no longer

manufactured by Elo), remove the jumper at J5.

Touchscreen Type J5

AccuTouch installed (shipped setting)

DuraTouch not installed

Reserved Jumpers

Jumpers J0, J1, J2, J3, and J6 on the E271-2202 controller are reserved. They

should not be installed.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 138 139

SmartSet 1
Trademark Acknowledgements 4
Copyright 4
Limited Warranty 4
Governing Law 6
Introduction 11
E271-2200 Serial Controller 12
E271-2210 Serial Controller 12
THEORY OF OPERATION 13
The AccuTouch Touchscreen 14
The DuraTouch Touchscreen 15
ABOUT THIS MANUAL 16
Controller Jumper Settings 17
E271-2200 SERIAL CONTROLLER 20
E271-2210 SERIAL CONTROLLER 22
Selecting the Data Format 24
Hardware Handshaking 25
Emulation Mode 26
Reserved Jumpers 26
E271-2201 PC-BUS CONTROLLER 27
Selecting the Base I/O Port 28
Selecting the Interrupt (IRQ) 29
8- and 12-Bit Modes 31
ICRO CHANNEL CONTROLLER 32
Installation and Connections 35
Serial Controller Connections 36
1-S, 6-X, 7-Y, 8-L, 9-H 38
E271-2201 Connections 41
E271-2202 Installation 42
E271-2202 Connections 42
DIAGNOSTIC LEDS 43
SmartSet Tutorial 45
RUNNING SMARTSET 46
Main Menu Categories 48
SAMPLE SMARTSET SESSION 49
Enabling Touch Reporting 50
Changing the Touch Mode 50
Calibration 50
Saving the Setup 54
WHERE TO GO FROM HERE 56
Software Interface 57
Commands and Responses 58
Commands and Acknowledgements 59
INTERFACE SPECIFICS 61
Bus Controllers 65
SAMPLE DRIVER CODE 67
Sample Driver Code 59 69
Sample Driver Code 61 71
Sample Driver Code 63 73
Sample Driver Code 65 75
Sample Driver Code 67 77
Sample Driver Code 69 79
Interrupt-Driven Code 80
Command Reference 81
COMMAND DESCRIPTIONS 82
Acknowledge ('a') 83
Configuration ('g') 93
ID ('i') 95
Jumpers ('j') 96
Owner ('o') 104
Reset ('R') 109
Touch ('t') 112
Command Descriptions 103 113
Optional Software Protocols 115
SmartSet ASCII Mode 116
E261-280 Emulation 118
9600 baud + Mode 119
E271-2201 CONTROLLER 122
E271-2201 Controller 115 125
And here is the program: 125
Software Protocols 126
Appendix Appendix BB 127
Specifications 131
Environmental 133
Physical Characteristics 133
Agency Approvals 134
AND E271-2202 CONTROLLERS 135
Electrical 135

Komentarze do niniejszej Instrukcji

Brak uwag

Elo TouchSystems 2201L Dokumentacja Strona 34

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Nie Elo TouchSystems 2201L